MyLife Camaps FX - Everything you need to know!

I open new discussion thread dedicated to "MyLife Camps FX", this innovative system for type 1 diabetes management uses an intelligent algorithm to automatically adjust insulin, helping to keep blood glucose levels within an objective range.

What is this thread about?

Greetings to all!

I start with a first question, I have recently updated the latest version, and I think that since then when trying to read the free freestyle 3 with the mobile passing it, it does not work, I see a message that says something like this: "NFC label not linked toan app ".

I worry that I have problems to start sensors, I will see it in a few days when the sensor I have now ends.

Has anyone happened to him?

Thank you!

Hi Fer, I have started a sensor after the update and perfect, I did not give me any problem.

Greetings

@nimrod100 Has the message happened to you?

I put a screenshot here.

fer said:
@nimrod100 Has the message happened to you?

I put a screenshot here.

Well no, I just tried and nothing comes out, vibrates but nothing more, I suppose it will depend on the mobile ... and the configuration of the NFC ... anyway as the NFC works if you have the application in the foreground when you tryActivate the new sensor The reading data goes to the active application and should not give problems ... the message that comes out is like when you make a payment and by default opens a Wallet type application, in this case it does not have any default...

Greetings

A curiosity, because you read the sensor with the NFC and not through the Bluetooth?minute and not every 5 as with the dexcom

@jasom the normal use with the bluetooth, but to start it, the phone is normally put on the sensor and NFC is used (or so I understand), sometimes, during the normal use of the sensor, thesignal and in those moments I usually pass the mobile through the sensor (as a way of reactivating it).

The issue is that when I pass it now, I think that just after the update, because the message that commented above appears.

Good again!

I share you, that once the old sensor is over, when I put on a new one there was no way to start it, so after trying several things, I ended up doing the following:

* Used a configuration option "Restore NFC functionality"
* Uninstalled and re -install fx camps

Upon installing Camaps FX I have had to make an initial configuration, after which I have normally accessed the application and I have been able to start the sensor normally.

Apart from, I wanted to put an insulin bolus, when accessing the screen a message has appeared that would take a while (6 minutes) in the connection with the pump because I was synchronizing data (or something like that).

After all this, I am already using Camaps FX, the insulin pump and the sensor with total normality.

Technology Aventurillas .... We are going to end up being an IT team of diabetes :)

A truquis post would be fine.

Hello reflooto a little thread.I have been offered the option to choose between 3 closed handle systems (I am from Andalusia and it is the first time they offer me).I am a diabetic with 43 years of more or less controlled evolution (around 6 HB glycosilada).I play with the doses daily and with the sensor because I am tight.In order not to roll up I go to the grain, they have offered me the following options

1) Medtronic 670g & AMP;780g

2) Tandem Control IQ

3) FX camps..))

1) which would you choose?2) All can be used with any sensor?skin?

4) Finally I understand that if I bath or do swimming I have to disconnect the bomb right? In the end they are very "chorras" questions but I appreciate your opinions.> Thank you very much beforehand </s

I met the same situation a year ago, to summarize, I opted for option 3." Link target = "_blank"> Link

@suguguis

Thank you very much @fer For the prompt response.I start reading the post sent

a greeting

fer said:
@Fer said:

@jasom the normal use with the bluetooth, but to start it, the phone is normally put on the sensor and use NFC (or so I understand), sometimes, during the normal use of the sensor, the signal is lost and inI usually pass the mobile at the sensor (as a way to reactivate it).

The issue is that when I pass it now, I think that just after the update, because the message that commented above appears.

I have a question with the "Mylife Camaps FX" app and the YpSopump bomb ...

In the Menu App [Settings \ Personal Glucose Objective] no matter how high it puts values ​​here(eg 115), it seems that the app does not take these values ​​into account, since in "Auto Mode" it is taking me to continue hypos, without having active insulin, for example at dawn after dinner hours.

I understand that the app should bring glucose levels to those established in "objective glucose" and when it comes to suspend the infusion, but crosses them below and continues to put basal/correction, even being glucose below 80 mg/dl taking me to a hicc.

Notes: Insulin Fiasp.Menu [Settings \ Bowling assistant \ Active insulin duration] = 3.5 hours.Menu[Settings \ Bowling assistant \ glucose target] = 110 mg/dl.

Have you had this same experience?

Good morning @Kenyi

The sensor was a very rare thing, it only happened to me that time, I had to uninstall the app, restart the mobile and install again, after that I could already start the new sensor.

The glucose target, I would say that it works well for me, for a while I had it higher than the 105 or 104 that come by default, and I would say that I kept it well.

If you get a lot at night, you could try to activate the Easy-Off mode, configure it for a few hours and look to see how you get up, with that it is supposed to supply you 30% less basal.

Greetings,